You need it done? Jobber 6 can do it.
Here are just some of the examples the Jobber 6
can perform. With the help of the 63 page detailed instruction
manual that comes with Jobber 6, no job is too complicated for the Jobber 6.
The Jobber 6 will cut costs, errors & rework to insure higher profits.
Click any of the YouTube buttons to watch a video on how each task is performed. This is just a few videos we have posted. To see a list of all of them, check out our YOUTUBE page or Google Plus page. Click either button below.
and 
|
Right Triangles
Given any 2 Parts of a right triangle, be able
to complete the whole triangle instantly... (run,
rise, angle, pitch, tangent or slope)

-------------------------------------------------------------
Oblique Triangles
Given 2 angles and one side or 2 sides and 1 angle.
You have your angle instantly.
Need the Area??? The Jobber 6 can give you that
too. |
|

Bolt Circles can be solved in seconds. Know the
diameter? Know the bolt pattern? The Jobber 6 will give you everything you need
to know to complete it

|
If you know any 2 parts of a
circle, let the Jobber 6 will tell you all the rest.
Need the area? Once again the Jobber 6 can give
it. |
|
|
Here is an example of how the Jobber 6 could solve a
more complex circle using the segmented rise function.
All that is known is the radius (12'-8 1/4") and the
cord (23'-6"). Default spacing was set to 1'-10". with special spacing changed
2'-4" and 2'-1".
With the Jobber 6, the everything you need to know
about this circle can be know in seconds.

|
|
With the rake-up function on the
Jobber 6, you can solve the increasing length for studs in a raked wall or gable
end. Using the stored values of the run, rise and slope, you can then set the
default spacing for each.
The example to the right, the default spacing is set
to 1'-4". But at any time, a special spacing can be added. In this case, special
spacing was set at 1'-6" and also 2'-6". Once this special spacing has been
done, the default spacing will automatically go back to the 1'-4", the spacing
you already set at the beginning.
The rake-down function works in a very similair way
as the
rake-up function with the exception it starts with the high side of
the triangle and works it's way down. |


|
|
|
Simple to the most complex roof
systems are no match for the Jobber 6.
In this example, we have a 5 1/2 to 12 pitch and a
24'-0" span. In a matter of moments, we can find the common rafter length, hip
pitch, hip length and the jack lengths just by the touch of a few
buttons.
If you are working with a hip roof, you can figure
your Jack rafter lengths (see picture below). Set your default spacing to
whatever you desire and off you go! It really is that easy.

|

|
|
|
Stairs have you baffled?
Do you have the floor to floor height, the maximum
riser height, the length of the tread? If you do, you have everything you need
in order to solve this entire stair design.
The Jobber 6 will let you know every detail of the
stairs based on the information you provide.
It is that easy!! And with
the 0 to 15 keypad, your number of keystrokes is drastically reduced and time
spent is easily cut in half.

|
|
|
Find degrees for miter
cuts and miter pitch in just a four steps.

|
|
Figuring cubic yards of
contrete is something every builder and contractor has to do. One of the new
features on the Jobber 6 is a cubic yard button.
Figure anything from footers to clabs to concrete
walls. How much concrete do you need? Don't under estimate or over estimate. Hit
a few buttons on your Jobber 6 and now exactly what it will
take.

|

|
 |
Pouring an odd shaped slab? How many yards of concrete are
required?
Seem Complicated? Not for the Jobber 6. Have your answer in
less than a minute! |
|
Need to square up a floor? A
wall? If you know any 2 parts, the run, rise, or slope, the Jobber 6 will give
you the missing part of the puzzle.

|
 |